300-135 TSHOOT Online Test-Troubleshooting and Maintaining Cisco IP Networks

Currently, our 300-135 TSHOOT online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

Topic 1
Exhibit:

A network administrator is troubleshooting an EIGRP connection between RouterA, IP address 10.1.2.1, and RouterB, IP address 10.1.2.2. Given the debug output on RouterA, which two statements are true? (Choose two.)

RouterA received a hello packet with mismatched autonomous system numbers.

RouterA received a hello packet with mismatched hello timers.

RouterA received a hello packet with mismatched authentication parameters.

RouterA received a hello packet with mismatched metric-calculation mechanisms.

RouterA will form an adjacency with RouterB.

RouterA will not form an adjacency with RouterB.

When troubleshooting an EIGRP connectivity problem, you notice that two connected EIGRP routers are not becoming EIGRP neighbors. A ping between the two routers was successful. What is the next thing that should be checked?

Verify that the EIGRP hello and hold timers match exactly.

Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip
EIGRP peer command.

Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip
EIGRP traffic command.

Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router.

Which IPsec mode will encrypt a GRE tunnel to provide multiprotocol support and reduced overhead?

3DES

multipoint GRE

tunnel

transport

Which three features are benefits of using GRE tunnels in conjunction with IPsec for building site?to-site VPNs? (Choose three.)

allows dynamic routing over the tunnel

supports multi-protocol (non-IP) traffic over the tunnel

reduces IPsec headers overhead since tunnel mode is used

simplifies the ACL used in the crypto map

uses Virtual Tunnel Interface (VTI) to simplify the IPsec VPN configuration

Which statement is true about an IPsec/GRE tunnel?

The GRE tunnel source and destination addresses are specified within the IPsec transform set.

An IPsec/GRE tunnel must use IPsec tunnel mode.

GRE encapsulation occurs before the IPsec encryption process.

Crypto map ACL is not needed to match which traffic will be protected.

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolate the cause of this fault and answer the following question. The fault condition is related to which technology?

NTP

IP DHCP Server

Ipv4 OSPF Routing

Ipv4 EIGRP Routing.

Ipv4 Route Redistribution.

Ipv6 RIP Routing

Ipv6 OSPF Routing

Ipv4 and Ipv6 Interoperability

Ipv4 layer 3 security.

Under the global configuration, delete the no ip dhcp use vrf connected command.

Under the IP DHCP pool configuration, delete the default -router 10.2.1.254 command and enter the default-router 10.1.4.5 command.

Under the IP DHCP pool configuration, delete the network 10.2.1.0 255.255.255.0 command and enter the network 10.1.4.0 255.255.255.0 command.

Under the IP DHCP pool configuration, issue the no ip dhcp excluded-address 10.2.1.1 10.2.1.253 command and enter the ip dhcp excluded-address 10.2.1.1 10.2.1.2 command.

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10. Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

NTP

HSRP

IP DHCP Helper

IPv4 EIGRP Routing

IPv6 RIP Routing

IPv4 layer 3 security

Switch-to-Switch Connectivity

Loop Prevention

Access Vlans

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10. Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

Under the interface vlan 10 configuration enter standby 10 preempt command.

Under the track 1 object configuration delete the threshold metric up 1 down 2 command and enter the threshold metric up 61 down 62 command.

Under the track 10 object configuration delete the threshold metric up 61 down 62 command and enter the threshold metric up 1 down 2 command.

Under the interface vlan 10 configuration delete the standby 10 track1 decrement 60 command and enter the standby 10 track 10 decrement 60 command.

The implementations group has been using the test bed to do a ‘proof-of-concept’. After several changes to the network addressing, routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2(2026::102:1). Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

DSW1

DSW2

ASW1

ASW2

NTP

IPv4 OSPF Routing

IPv6 OSPF Routing

IPv4 layer 3 security

Under the interface Serial 0/0/0.23 configuration enter the ipv6 ospf 6 area 0 command.

Under the interface Serial0/0/0.12 configuration enter the ipv6 ospf 6 area 12 command.

Under ipv6 router ospf 6 configuration enter the network 2026::1:/122 area 0 command.

Under ipv6 router ospf 6 configuration enter no passive-interface default command.

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

NTP

IP DHCP Helper

IPv4 EIGRP Routing

IPv6 RIP Routing

IPv4 layer 3 security

Switch-to-Switch Connectivity

Loop Prevention

Access Vlans

Port Security

VLAN ACL / Port ACL

Switch Virtual Interface

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

Under the global configuration mode enter no access-list 10 command.

Under the global configuration mode enter no access-map vlan 10 command.

Under the global configuration mode enter no vlan access-map test1 10 command.

Under the global configuration mode enter no vlan filter test1 vlan-list 10 command.

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

Disable auto summary on the EIGRP process

Enable EIGRP on the FastEthernet0/0 and FastEthernet0/1 interface using the no passive-interface command.

Change the AS number on the EIGRP routing process from 1 to 10 to much the AS number used on DSW1 and DSW2.

Under the EIGRP process, delete the network 10.1.4.0 0.0.0.255 command and enter the network 10.1.4.4 0.0.0.252 and 10.1.4.8 0.0.0.252 commands.

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. Which is the solution to the fault condition?

Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF_ to_ EIGRP command and enter the redistribute ospf 1 route-map OSPF – > EIGRP command.

Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF_ to_ EIGRP command and enter the redistribute ospf 6 metric route-map OSPF – > EIGRP command.

Under the OSPF process, delete the redistribute eigrp10 subnets route-map EIGPR ->OSPF command and enter the redistribute eigrp10 subnets route-map OSPF – > EIGRP command.

Under the OSPF process, delete the redistribute eigrp10 subnets route-map EIGPR ->OSPF command and enter the redistribute eigrp10 subnets route-map EIGPR – > OSPF command.

Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF _to_ EIGRP command and enter redistribute ospf 1 metric 100000 100 100 1 15000 route_ map OSPF _to _EIGRP command

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

DSW1

DSW2

ASW1

ASW2

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10. Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

DSW1

DSW2

ASW1

ASW2

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

NTP

Switch-to-Switch Connectivity

Access Vlans

Port Security

VLAN ACL / Port ACL

Switch Virtual Interface

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port-security interface configuration commands. Then in exec mode clear errdisable interface fa 1/01 – 2 vlan 10 command

In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port-security, followed by shutdown, no shutdown interface configuration commands.

In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port-security interface configuration commands.

Question 1 of 20

CCNP Exams Test Base

New CCNP Exams from January 30, 2015

Note:

Tag Archives: 300-135 TSHOOT online test

300-135 TSHOOT Online Test-Troubleshooting and Maintaining Cisco IP Networks

Recent Posts

Tags

Links