CCNA Routing and Switching – CCNP Exams Test Base

Posted on 八月 9, 2016 by admin

200-105 ICND2 Interconnecting Cisco Networking Devices Part 2

Interconnecting Cisco Networking Devices Part 2 is the exam name of 200-105 ICND2 test. There are 45-55 questions in real Cisco 200-105 ICND2 exam, which will take the candidates 90 minutes to complete the test. The Associated Certification is CCNA Routing & Switching. The available languages are English and Japanese. Candidates can register Cisco 200-105 ICND2 exam at Pearson VUE testing center.

Knowing Cisco 200-105 ICND2 exam topics are valuable in your preparation.

1.0 LAN Switching Technologies 26%

1.1 Configure, verify, and troubleshoot VLANs (normal/extended range) spanning multiple switches
1.1.a Access ports (data and voice)
1.1.b Default VLAN
1.2 Configure, verify, and troubleshoot interswitch connectivity
1.2.a Add and remove VLANs on a trunk
1.2.b DTP and VTP (v1&v2)
1.3 Configure, verify, and troubleshoot STP protocols
1.3.a STP mode (PVST+ and RPVST+)
1.3.b STP root bridge selection
1.4 Configure, verify, and troubleshoot STP-related optional features
1.4.a PortFast
1.4.b BPDU guard
1.5 Configure, verify, and troubleshoot (Layer 2/Layer 3) EtherChannel
1.5.a Static
1.5.b PAGP
1.5.c LACP
1.6 Describe the benefits of switch stacking and chassis aggregation
1.7 Describe common access layer threat mitigation techniques
1.7.a 802.1x
1.7.b DHCP snooping
1.7.c Nondefault native VLAN

2.0 Routing Technologies 29%

2.1 Configure, verify, and troubleshoot Inter-VLAN routing
2.1.a Router on a stick
2.1.b SVI
2.2 Compare and contrast distance vector and link-state routing protocols
2.3 Compare and contrast interior and exterior routing protocols
2.4 Configure, verify, and troubleshoot single area and multiarea OSPFv2 for IPv4 (excluding authentication, filtering, manual summarization, redistribution, stub, virtual-link, and LSAs)
2.5 Configure, verify, and troubleshoot single area and multiarea OSPFv3 for IPv6 (excluding authentication, filtering, manual summarization, redistribution, stub, virtual-link, and LSAs)
2.6 Configure, verify, and troubleshoot EIGRP for IPv4 (excluding authentication, filtering, manual summarization, redistribution, stub)
2.7 Configure, verify, and troubleshoot EIGRP for IPv6 (excluding authentication, filtering, manual summarization, redistribution, stub)

3.0 WAN Technologies 16%

3.1 Configure and verify PPP and MLPPP on WAN interfaces using local authentication
3.2 Configure, verify, and troubleshoot PPPoE client-side interfaces using local authentication
3.3 Configure, verify, and troubleshoot GRE tunnel connectivity
3.4 Describe WAN topology options
3.4.a Point-to-point
3.4.b Hub and spoke
3.4.c Full mesh
3.4.d Single vs dual-homed
3.5 Describe WAN access connectivity options
3.5.a MPLS
3.5.b MetroEthernet
3.5.c Broadband PPPoE
3.5.d Internet VPN (DMVPN, site-to-site VPN, client VPN)
3.6 Configure and verify single-homed branch connectivity using eBGP IPv4 (limited to peering and route advertisement using Network command only)

4.0 Infrastructure Services 14%

4.1 Configure, verify, and troubleshoot basic HSRP
4.1.a Priority
4.1.b Preemption
4.1.c Version
4.2 Describe the effects of cloud resources on enterprise network architecture
4.2.a Traffic path to internal and external cloud services
4.2.b Virtual services
4.2.c Basic virtual network infrastructure
4.3 Describe basic QoS concepts
4.3.a Marking
4.3.b Device trust
4.3.c Prioritization
4.3.c. [i] Voice
4.3.c. [ii] Video
4.3.c. [iii] Data
4.3.d Shaping
4.3.e Policing
4.3.f Congestion management
4.4 Configure, verify, and troubleshoot IPv4 and IPv6 access list for traffic filtering
4.4.a Standard
4.4.b Extended
4.4.c Named
4.5 Verify ACLs using the APIC-EM Path Trace ACL analysis tool

5.0 Infrastructure Maintenance 15%

5.1 Configure and verify device-monitoring protocols
5.1.a SNMPv2
5.1.b SNMPv3
5.2 Troubleshoot network connectivity issues using ICMP echo-based IP SLA
5.3 Use local SPAN to troubleshoot and resolve problems
5.4 Describe device management using AAA with TACACS+ and RADIUS
5.5 Describe network programmability in enterprise network architecture
5.5.a Function of a controller
5.5.b Separation of control plane and data plane
5.5.c Northbound and southbound APIs
5.6 Troubleshoot basic Layer 3 end-to-end connectivity issues

Posted on 八月 9, 2016 by admin

100-105 ICND1 Interconnecting Cisco Networking Devices Part 1

Interconnecting Cisco Networking Devices Part 1 is the full name of 100-105 ICND1 test. There are 45-55 questions in real Cisco 100-105 ICND1 exam, which will take the candidates 90 minutes to complete the test. The available languages are English and Japanese. The Associated Certifications are CCENT, CCNA Routing & Switching, CCDA, CCNA Security, CCNA Wireless. Candidates can register Cisco 100-105 ICND1 exam at Pearson VUE testing center.

It is useful for the candidates to know 100-105 ICND1 Interconnecting Cisco Networking Devices Part 1 exam topics.

1.0 Network Fundamentals 20%

1.1 Compare and contrast OSI and TCP/IP models
1.2 Compare and contrast TCP and UDP protocols
1.3 Describe the impact of infrastructure components in an enterprise network
1.3.a Firewalls
1.3.b Access points
1.3.c Wireless controllers
1.4 Compare and contrast collapsed core and three-tier architectures
1.5 Compare and contrast network topologies
1.5.a Star
1.5.b Mesh
1.5.c Hybrid
1.6 Select the appropriate cabling type based on implementation requirements
1.7 Apply troubleshooting methodologies to resolve problems
1.7.a Perform fault isolation and document
1.7.b Resolve or escalate
1.7.c Verify and monitor resolution
1.8 Configure, verify, and troubleshoot IPv4 addressing and subnetting
1.9 Compare and contrast IPv4 address types
1.9.a Unicast
1.9.b Broadcast
1.9.c Multicast
1.10 Describe the need for private IPv4 addressing
1.11 Identify the appropriate IPv6 addressing scheme to satisfy addressing requirements in a LAN/WAN environment
1.12 Configure, verify, and troubleshoot IPv6 addressing
1.13 Configure and verify IPv6 Stateless Address Auto Configuration
1.14 Compare and contrast IPv6 address types
1.14.a Global unicast
1.14.b Unique local
1.14.c Link local
1.14.d Multicast
1.14.e Modified EUI 64
1.14.f Autoconfiguration
1.14.g Anycast

2.0 LAN Switching Fundamentals 26%

2.1 Describe and verify switching concepts
2.1.a MAC learning and aging
2.1.b Frame switching
2.1.c Frame flooding
2.1.d MAC address table
2.2 Interpret Ethernet frame format
2.3 Troubleshoot interface and cable issues (collisions, errors, duplex, speed)
2.4 Configure, verify, and troubleshoot VLANs (normal range) spanning multiple switches
2.4.a Access ports (data and voice)
2.4.b Default VLAN
2.5 Configure, verify, and troubleshoot interswitch connectivity
2.5.a Trunk ports
2.5.b 802.1Q
2.5.c Native VLAN
2.6 Configure and verify Layer 2 protocols
2.6.a Cisco Discovery Protocol
2.6.b LLDP
2.7 Configure, verify, and troubleshoot port security
2.7.a Static
2.7.b Dynamic
2.7.c Sticky
2.7.d Max MAC addresses
2.7.e Violation actions
2.7.f Err-disable recovery

3.0 Routing Fundamentals 25%

4.0 Infrastructure Services 15%

4.1 Describe DNS lookup operation
4.2 Troubleshoot client connectivity issues involving DNS
4.3 Configure and verify DHCP on a router (excluding static reservations)
4.3.a Server
4.3.b Relay
4.3.c Client
4.3.d TFTP, DNS, and gateway options
4.4 Troubleshoot client- and router-based DHCP connectivity issues
4.5 Configure and verify NTP operating in client/server mode
4.6 Configure, verify, and troubleshoot IPv4 standard numbered and named access list for routed interfaces
4.7 Configure, verify, and troubleshoot inside source NAT
4.7.a Static
4.7.b Pool
4.7.c PAT

5.0 Infrastructure Maintenance 14%

5.1 Configure and verify device-monitoring using syslog
5.2 Configure and verify device management
5.2.a Backup and restore device configuration
5.2.b Using Cisco Discovery Protocol and LLDP for device discovery
5.2.c Licensing
5.2.d Logging
5.2.e Timezone
5.2.f Loopback
5.3 Configure and verify initial device configuration
5.4 Configure, verify, and troubleshoot basic device hardening
5.4.a Local authentication
5.4.b Secure password
5.4.c Access to device
5.4.c. [i] Source address
5.4.c. [ii] Telnet/SSH
5.4.d Login banner
5.5 Perform device maintenance
5.5.a Cisco IOS upgrades and recovery (SCP, FTP, TFTP, and MD5 verify)
5.5.b Password recovery and configuration register
5.5.c File system management
5.6 Use Cisco IOS tools to troubleshoot and resolve problems
5.6.a Ping and traceroute with extended option
5.6.b Terminal monitor
5.6.c Log events

Posted on 六月 14, 2016 by admin

200-125 CCNA Cisco Certified Network Associate Exam

Cisco Certified Network Associate Exam is the full name of 200-125 CCNA test. There are 50-60 questions in real Cisco 200-125 CCNA exam, which will take the candidates 90 minutes to complete the test. The Associated Certification is CCNA Routing and Switching. The available languages are English and Japanese. Candidates can register Cisco 200-125 CCNA exam at Pearson VUE testing center.

It is helpful for the candidates to know 200-125 CCNA Cisco Certified Network Associate Exam topics.

1.0 Network Fundamentals 15%

1.1 Compare and contrast OSI and TCP/IP models
1.2 Compare and contrast TCP and UDP protocols
1.3 Describe the impact of infrastructure components in an enterprise network
1.3.a Firewalls
1.3.b Access points
1.3.c Wireless controllers
1.4 Describe the effects of cloud resources on enterprise network architecture
1.4.a Traffic path to internal and external cloud services
1.4.b Virtual services
1.4.c Basic virtual network infrastructure
1.5 Compare and contrast collapsed core and three-tier architectures
1.6 Compare and contrast network topologies
1.6.a Star
1.6.b Mesh
1.6.c Hybrid
1.7 Select the appropriate cabling type based on implementation requirements
1.8 Apply troubleshooting methodologies to resolve problems
1.8.a Perform and document fault isolation
1.8.b Resolve or escalate
1.8.c Verify and monitor resolution
1.9 Configure, verify, and troubleshoot IPv4 addressing and subnetting
1.10 Compare and contrast IPv4 address types
1.10.a Unicast
1.10.b Broadcast
1.10.c Multicast
1.11 Describe the need for private IPv4 addressing
1.12 Identify the appropriate IPv6 addressing scheme to satisfy addressing requirements in a LAN/WAN environment
1.13 Configure, verify, and troubleshoot IPv6 addressing
1.14 Configure and verify IPv6 Stateless Address Auto Configuration
1.15 Compare and contrast IPv6 address types
1.15.a Global unicast
1.15.b Unique local
1.15.c Link local
1.15.d Multicast
1.15.e Modified EUI 64
1.15.f Autoconfiguration
1.15.g Anycast

2.0 LAN Switching Technologies 21%

2.1 Describe and verify switching concepts
2.1.a MAC learning and aging
2.1.b Frame switching
2.1.c Frame flooding
2.1.d MAC address table
2.2 Interpret Ethernet frame format
2.3 Troubleshoot interface and cable issues (collisions, errors, duplex, speed)
2.4 Configure, verify, and troubleshoot VLANs (normal/extended range) spanning multiple switches
2.4.a Access ports (data and voice)
2.4.b Default VLAN
2.5 Configure, verify, and troubleshoot interswitch connectivity
2.5.a Trunk ports
2.5.b Add and remove VLANs on a trunk
2.5.c DTP, VTP (v1&v2), and 802.1Q
2.5.d Native VLAN
2.6 Configure, verify, and troubleshoot STP protocols
2.6.a STP mode (PVST+ and RPVST+)
2.6.b STP root bridge selection
2.7 Configure, verify and troubleshoot STP related optional features
2.7.a PortFast
2.7.b BPDU guard
2.8 Configure and verify Layer 2 protocols
2.8.a Cisco Discovery Protocol
2.8.b LLDP
2.9 Configure, verify, and troubleshoot (Layer 2/Layer 3) EtherChannel
2.9.a Static
2.9.b PAGP
2.9.c LACP
2.10 Describe the benefits of switch stacking and chassis aggregation

3.0 Routing Technologies 23%

3.1 Describe the routing concepts
3.1.a Packet handling along the path through a network
3.1.b Forwarding decision based on route lookup
3.1.c Frame rewrite
3.2 Interpret the components of a routing table
3.2.a Prefix
3.2.b Network mask
3.2.c Next hop
3.2.d Routing protocol code
3.2.e Administrative distance
3.2.f Metric
3.2.g Gateway of last resort
3.3 Describe how a routing table is populated by different routing information sources
3.3.a Admin distance
3.4 Configure, verify, and troubleshoot inter-VLAN routing
3.4.a Router on a stick
3.4.b SVI
3.5 Compare and contrast static routing and dynamic routing
3.6 Compare and contrast distance vector and link state routing protocols
3.7 Compare and contrast interior and exterior routing protocols
3.8 Configure, verify, and troubleshoot IPv4 and IPv6 static routing
3.8.a Default route
3.8.b Network route
3.8.c Host route
3.8.d Floating static
3.9 Configure, verify, and troubleshoot single area and multi-area OSPFv2 for IPv4 (excluding authentication, filtering, manual summarization, redistribution, stub, virtual-link, and LSAs)
3.10 Configure, verify, and troubleshoot single area and multi-area OSPFv3 for IPv6 (excluding authentication, filtering, manual summarization, redistribution, stub, virtual-link, and LSAs)
3.11 Configure, verify, and troubleshoot EIGRP for IPv4 (excluding authentication, filtering, manual summarization, redistribution, stub)
3.12 Configure, verify, and troubleshoot EIGRP for IPv6 (excluding authentication, filtering, manual summarization, redistribution, stub)
3.13 Configure, verify, and troubleshoot RIPv2 for IPv4 (excluding authentication, filtering, manual summarization, redistribution)
3.14 Troubleshoot basic Layer 3 end-to-end connectivity issues

4.0 WAN Technologies 10%

4.1 Configure and verify PPP and MLPPP on WAN interfaces using local authentication
4.2 Configure, verify, and troubleshoot PPPoE client-side interfaces using local authentication
4.3 Configure, verify, and troubleshoot GRE tunnel connectivity
4.4 Describe WAN topology options
4.4.a Point-to-point
4.4.b Hub and spoke
4.4.c Full mesh
4.4.d Single vs dual-homed
4.5 Describe WAN access connectivity options
4.5.a MPLS
4.5.b Metro Ethernet
4.5.c Broadband PPPoE
4.5.d Internet VPN (DMVPN, site-to-site VPN, client VPN)
4.6 Configure and verify single-homed branch connectivity using eBGP IPv4 (limited to peering and route advertisement using Network command only)
4.7 Describe basic QoS concepts
4.7.a Marking
4.7.b Device trust
4.7.c Prioritization
4.7.c. [i] Voice
4.7.c. [ii] Video
4.7.c. [iii] Data
4.7.d Shaping
4.7.e Policing
4.7.f Congestion management

5.0 Infrastructure Services 10%

5.1 Describe DNS lookup operation
5.2 Troubleshoot client connectivity issues involving DNS
5.3 Configure and verify DHCP on a router (excluding static reservations)
5.3.a Server
5.3.b Relay
5.3.c Client
5.3.d TFTP, DNS, and gateway options
5.4 Troubleshoot client- and router-based DHCP connectivity issues
5.5 Configure, verify, and troubleshoot basic HSRP
5.5.a Priority
5.5.b Preemption
5.5.c Version
5.6 Configure, verify, and troubleshoot inside source NAT
5.6.a Static
5.6.b Pool
5.6.c PAT
5.7 Configure and verify NTP operating in a client/server mode

6.0 Infrastructure Security 11%

6.1 Configure, verify, and troubleshoot port security
6.1.a Static
6.1.b Dynamic
6.1.c Sticky
6.1.d Max MAC addresses
6.1.e Violation actions
6.1.f Err-disable recovery
6.2 Describe common access layer threat mitigation techniques
6.2.a 802.1x
6.2.b DHCP snooping
6.2.c Nondefault native VLAN
6.3 Configure, verify, and troubleshoot IPv4 and IPv6 access list for traffic filtering
6.3.a Standard
6.3.b Extended
6.3.c Named
6.4 Verify ACLs using the APIC-EM Path Trace ACL analysis tool
6.5 Configure, verify, and troubleshoot basic device hardening
6.5.a Local authentication
6.5.b Secure password
6.5.c Access to device
6.5.c. [i] Source address
6.5.c. [ii] Telnet/SSH
6.5.d Login banner
6.6 Describe device security using AAA with TACACS+ and RADIUS

7.0 Infrastructure Management 10%

7.1 Configure and verify device-monitoring protocols
7.1.a SNMPv2
7.1.b SNMPv3
7.1.c Syslog
7.2 Troubleshoot network connectivity issues using ICMP echo-based IP SLA
7.3 Configure and verify device management
7.3.a Backup and restore device configuration
7.3.b Using Cisco Discovery Protocol or LLDP for device discovery
7.3.c Licensing
7.3.d Logging
7.3.e Timezone
7.3.f Loopback
7.4 Configure and verify initial device configuration
7.5 Perform device maintenance
7.5.a Cisco IOS upgrades and recovery (SCP, FTP, TFTP, and MD5 verify)
7.5.b Password recovery and configuration register
7.5.c File system management
7.6 Use Cisco IOS tools to troubleshoot and resolve problems
7.6.a Ping and traceroute with extended option
7.6.b Terminal monitor
7.6.c Log events
7.6.d Local SPAN
7.7 Describe network programmability in enterprise network architecture
7.7.a Function of a controller
7.7.b Separation of control plane and data plane
7.7.c Northbound and southbound APIs

Posted on 三月 25, 2015 by admin

200-101 ICND2 Interconnecting Cisco Networking Devices Part 2

200-101 ICND2 is the official code of Interconnecting Cisco Networking Devices Part 2. The Associated Certification is CCNA Routing and Switching. There are 50-60 questions in real Cisco 200-101 ICND2 exam, which will take the candidates 75 minutes to complete the test. The available language is English. Candidates can register Cisco 200-101 exam at Pearson VUE testing center.

The 200-101 Interconnecting Cisco Networking Devices Part 2 (ICND2) is the exam associated with the CCNA Routing and Switching certification. Cisco 200-101 exam tests a candidate’s knowledge and skills required to successfully install, operate, and troubleshoot a small to medium-size enterprise branch network.

Cisco 200-101 ICND2 Free Online Test

To prepare Cisco 200-101 exam, it is useful for the candidates to know cisco 200-101 exam objectives.

21% 1.0 LAN Switching Technologies

1.1 Identify enhanced switching technologies
1.1.a RSTP
1.1.b PVSTP
1.1.c EtherChannels
1.2 Configure and verify PVSTP operation
1.2.a Describe root bridge election
1.2.b Spanning tree mode

26% 2.0 IP Routing Technologies

2.1 Describe the boot process of Cisco IOS routers
2.2 Configure and verify operation status of a serial interface
2.3 Manage Cisco IOS files
2.3.a Boot preferences
2.3.b Cisco IOS image(s)
2.3.c Licensing
2.3.c (i) Show license
2.3.c (ii) Change license
2.4 Differentiate methods of routing and routing protocols
2.4.a Administrative distance
2.4.b Split horizon
2.4.c Metric
2.4.d Next hop
2.5 Configure and verify OSPF (multi-area)
2.5.a Neighbor adjacencies
2.5.b OSPF states
2.5.c Configure OSPF v2
2.5.d Configure OSPF v3
2.5.e Router ID
2.5.f Understand LSA types and purpose
2.6 Configure and verify EIGRP (single AS)
2.6.a Feasible distance/feasible successors/administrative distance
2.6.b Feasibility condition
2.6.c Metric composition
2.6.d Router ID
2.6.e Auto summary
2.6.f Path selection
2.6.g Load balancing
2.6.g (i) Equal
2.6.g (ii) Unequal
2.6.h Passive interface

6% 3.0 IP Services

3.1 Recognize high availability (FHRP)
3.1.a VRRP
3.1.b HSRP
3.1.c GLBP
3.2 Configure and verify syslog
3.2.a Utilize syslog output
3.3 Describe SNMP v2 & v3

32% 4.0 Troubleshooting

4.1 Identify and correct common network problems
4.2 Utilize netflow data
4.3 Troubleshoot and resolve spanning tree operation issues
4.3.a Verify root switch
4.3.b Verify priority
4.3.c Verify mode is correct
4.3.d Verify port states
4.4 Troubleshoot and resolve routing issues
4.4.a Verify routing is enabled (SHIP protocols)
4.4.b Verify routing table is correct
4.4.c Verify correct path selection
4.5 Troubleshoot and resolve OSPF problems
4.5.a Verify neighbor adjancies
4.5.b Verify hello and dead timers
4.5.c Verify OSPF area
4.5.d Verify interface MTU
4.5.e Verify network types
4.5.f Verify neighbor states
4.5.g Review OSPF topology table `
4.6 Troubleshoot and resolve EIGRP problems
4.6.a Verify neighbor adjancies
4.6.b Verify AS number
4.6.c Verify load balancing
4.6.d Split horizon
4.7 Troubleshoot and resolve inter VLAN routing problems
4.7.a Verify connectivity
4.7.b Verify encapsulation
4.7.c Verify subnet
4.7.d Verify native VLAN
4.7.e Port mode trunk status
4.8 Troubleshoot and resolve WAN implementation issues
4.8.a Serial interfaces
4.8.b Frame relay
4.8.c PPP
4.9 Monitor NetFlow statistics
4.10 Troubleshoot EtherChannel problems

15% 5.0 WAN technologies

5.1 Identify different WAN Technologies
5.1.a Metro Ethernet
5.1.b VSAT
5.1.c Cellular 3G/4G
5.1.d MPLS
5.1.e T1/E1
5.1.f ISDN
5.1.g DSL
5.1.h Frame relay
5.1.i Cable
5.1.j VPN
5.2 Configure and verify a basic WAN serial connection
5.3 Configure and verify a PPP connection between Cisco routers
5.4 Configure and verify Frame Relay on Cisco routers
5.5 Implement and troubleshoot PPPoE

Posted on 三月 24, 2015 by admin

200-120 CCNA Cisco Certified Network Associate Exam

Cisco Certified Network Associate Exam is the full name of 200-120 CCNA test. The Associated Certifications is CCNA Routing and Switching. There are 50-60 questions in real Cisco 200-120 CCNA exam, which will take the candidates 90 minutes to complete the test. The available languages are English and Japanese. Candidates can register Cisco 200-120 CCNA exam at Pearson VUE testing center.

The 200-120 CCNA is the composite exam associated with the Cisco CCNA Routing and Switching certification. Cisco 200-120 CCNA exam tests a candidate’s knowledge and skills required to install, operate, and troubleshoot a small to medium size enterprise branch network.

Cisco 200-120 CCNA Free Online Test

Cisco 200-120 CCNA exam topics are helpful in your preparation. Below are the details from the offical website.

5% 1.0 Operation of IP Data Networks

1.1 Recognize the purpose and functions of various network devices such as Routers, Switches, Bridges and Hubs
1.2 Select the components required to meet a given network specification
1.3 Identify common applications and their impact on the network
1.4 Describe the purpose and basic operation of the protocols in the OSI and TCP/IP models
1.5 Predict the data flow between two hosts across a network
1.6 Identify the appropriate media, cables, ports, and connectors to connect Cisco network devices to other network devices and hosts in a LAN

20% 2.0 LAN Switching Technologies

2.1 Determine the technology and media access control method for Ethernet networks
2.2 Identify basic switching concepts and the operation of Cisco switches.
2.2.a Collision Domains
2.2.b Broadcast Domains
2.2.c Ways to switch
2.2.c (i) Store
2.2.c (ii) Forward
2.2.c (iii) Cut through
2.2.c (iv) CAM table
2.3 Configure and verify initial switch configuration including remote access management
2.3.a hostname
2.3.b Managment IP address
2.3.c IP default-gateway
2.3.d Local user and password
2.3.e Enable secret password
2.3.f Console and VTY logins
2.3.g exec-timeout
2.3.h Service password encryption
2.3.i copy run start
2.4 Verify network status and switch operation using basic utilities
2.4.a ping
2.4.b telnet
2.4.c SSH
2.5 Describe how VLANs create logically separate networks and the need for routing between them
2.5.a Explain network segmentation and basic traffic management concepts
2.6 Configure and verify VLANs
2.7 Configure and verify trunking on Cisco switches
2.7.a DTP (topic)
2.7.b Auto-negotiation
2.8 Identify enhanced switching technologies
2.8.a RSTP
2.8.b PVSTP
2.8.c EtherChannels
2.9 Configure and verify PVSTP operation
2.9.a Describe root bridge election
2.9.b Spanning tree mode

5% 3.0 IP addressing (IPv4/IPv6)

3.1 Describe the operation and necessity of using private and public IP addresses for IPv4 addressing
3.2 Identify the appropriate IPv6 addressing scheme to satisfy addressing requirements in a LAN/WAN environment
3.3 Identify the appropriate IPv4 addressing scheme using VLSM and summarization to satisfy addressing requirements in a LAN/WAN LAN/WAN environment
3.4 Describe the technological requirements for running IPv6 in conjunction with IPv4
3.4.a Dual stack
3.5 Describe IPv6 addresses
3.5.a Global unicast
3.5.b Multicast
3.5.c Link local
3.5.d Unique local
3.5.e EUI 64
3.5.f Auto-configuration

20% 4.0 IP Routing Technologies

4.1 Describe basic routing concepts
4.1.a Packet forwarding
4.1.b Router lookup process
4.1.c Process Switching/Fast Switching/CEF
4.2 Configure and verify utilizing the CLI to set basic router configuration
4.2.a Hostname
4.2.b Local user and password
4.2.c Enable secret password
4.2.d Console and VTY logins
4.2.e exec-timeout
4.2.f Service password encryption
4.2.g Interface IP Address
4.2.g (i) loopback
4.2.h banner
4.2.i MOTD
4.2.j copy run start
4.3 Configure and verify operation status of a device interface
4.3.a Serial
4.3.b Ethernet
4.4 Verify router configuration and network connectivity using
4.4.a ping
4.4.a (i) Extended ping
4.4.b traceroute
4.4.c telnet
4.4.d SSH
4.4.e Show cdp neighbors
4.5 Configure and verify routing configuration for a static or default route given specific routing requirements
4.6 Differentiate methods of routing and routing protocols
4.6.a Static vs. dynamic
4.6.b Link state vs. distance vector
4.6.c next hop
4.6.d IP routing table
4.6.e Passive Interfaces (how they work)
4.6.f Administrative distance
4.6.g split horizon
4.6.h metric
4.7 Configure and verify OSPF
4.7.a Benefit of single area
4.7.b Configure OSPv2
4.7.c Configure OSPv3
4.7.d Router ID
4.7.e Passive Interface
4.7.f Discuss multi-area OSPF
4.7.g Understand LSA types and purpose
4.8 Configure and verify interVLAN routing (Router on a stick)
4.8.a Sub interfaces
4.8.b Upstream routing
4.8.c Encapsulation
4.9 Configure SVI interfaces
4.10 Manage Cisco IOS Files
4.10.a Boot Preferences
4.10.b Cisco IOS Images (15)
4.10.c Licensing
4.10.c (i) Show license
4.10.c (ii) Change license
4.11 Configure and verify EIGRP (single AS)
4.11.a Feasible Distance/Feasible Successors/Administrative distance
4.11.b Feasibility condition
4.11.c Metric composition
4.11.d Router ID
4.11.e Auto summary
4.11.f Path Selection
4.11.g Load Balancing
4.11.g (i) Unequal
4.11.g (ii) Equal

10% 5.0 IP Services

5.1 Configure and verify DHCP (IOS Router)
5.1.a Configuring router interfaces to use DHCP
5.1.b DHCP options (Basic overview and functionality)
5.1.c Excluded addresses
5.1.d Lease time
5.2 Describe the types, features, and applications of ACLs
5.2.a Standard (editing and sequence numbers)
5.2.b Extended
5.2.c Named
5.2.d Numbered
5.2.e Log option
5.3 Configure and verify ACLs in a network environment
5.3.a Named
5.3.b Numbered
5.3.c Log option
5.4 Identify the basic operation of NAT
5.4.a Purpose
5.4.b Pool
5.4.c Static
5.4.d 1 to 1
5.4.e Overloading
5.4.f Source addressing
5.4.g One-way NAT
5.5 Configure and verify NAT for given network requirements
5.6 Configure and verify NTP as a client
5.7 Recognize High availability (FHRP)
5.7.a VRRP
5.7.b HSRP
5.7.c GLBP
5.8 Configure and verify syslog
5.8.a Utilize syslog output
5.9 Describe SNMP v2 and v3

10% 6.0 Network Device Security

6.1 Configure and verify network device security features
6.1.a Device password security
6.1.b Enable secret vs enable
6.1.c Transport
6.1.c (i) Disable telnet
6.1.c (ii) SSH
6.1.d VTYs
6.1.e Physical security
6.1.f Service password
6.1.g Describe external authentication methods
6.2 Configure and verify switch port security
6.2.a Sticky MAC
6.2.b MAC address limitation
6.2.c Static/dynamic
6.2.d Violation modes
6.2.d (i) errDisable
6.2.d (ii) shutdown
6.2.d (iii) protect restrict
6.2.e Shutdown unused ports
6.2.f errDisable recovery
6.2.g Assign unused ports to an unused VLAN
6.2.h Putting native VLAN to other than VLAN 1
6.3 Configure and verify ACLs to filter network traffic
6.4 Configure and verify an ACLs to limit telnet and SSH access to the router

20% 7.0 Troubleshooting

7.1 Troubleshoot and correct common problems associated with IP addressing and host configurations
7.2 Troubleshoot and resolve VLAN problems
7.2.a Identify that VLANs are configured
7.2.b Verify port membership correct
7.2.c Correct IP address is configured
7.3 Troubleshoot and resolve trunking problems on Cisco switches
7.3.a Verify correct trunk states
7.3.b Verify correct encapsulation id configured
7.3.c Correct VLANs allowed
7.4 Troubleshoot and resolve ACL issues
7.4.a Verify statistics
7.4.b Verify permitted networks
7.4.c Verify direction
7.4.c (i) Interface
7.5 Troubleshoot and resolve Layer 1 problems
7.5.a Framing
7.5.b CRC
7.5.c Runts
7.5.d Giants
7.5.e Dropped packets
7.5.f Late collisions
7.5.g Input/output errors
7.6 Identify and correct common network problems
7.7 Troubleshoot and resolve spanning tree operation issues
7.7.a Verify root switch
7.7.b Verify priority
7.7.c Verify mode is correct
7.7.d Verify port states
7.8 Troubleshoot and resolve routing issues
7.8.a Verify routing is enabled (SHIP protocols)
7.8.b Verify routing table is correct
7.8.c Verify correct path selection
7.9 Troubleshoot and resolve OSPF problems
7.9.a Verify neighbor adjacencies
7.9.b Verify hello and dead timers
7.9.c Verify OSPF area
7.9.d Verify interface MTU
7.9.e Verify network types
7.9.f Verify neighbor states
7.9.g Review OSPF topology table
7.10 Troubleshoot and resolve EIGRP problems
7.10.a Verify neighbor adjacencies
7.10.b Verify AS number
7.10.c Verify load balancing
7.10.d Split horizon
7.11 Troubleshoot and resolve interVLAN routing problems
7.11.a Verify connectivity
7.11.b Verify encapsulation
7.11.c Verify subnet
7.11.d Verify native VLAN
7.11.e Port mode trunk status
7.12 Troubleshoot and resolve WAN implementation issues
7.12.a Serial interfaces
7.12.b Frame relay
7.12.c PPP
7.13 Monitor NetFlow statistics
7.14 Troubleshoot EtherChannel problems

10% 8.0 WAN Technologies

8.1 Identify different WAN Technologies
8.1.a Metro Ethernet
8.1.b VSAT
8.1.c Cellular 3G/4G
8.1.d MPLS
8.1.e T1/E1
8.1.f ISDN
8.1.g DSL
8.1.h Frame relay
8.1.i Cable
8.1.j VPN
8.2 Configure and verify a basic WAN serial connection
8.3 Configure and verify a PPP connection between Cisco routers
8.4 Configure and verify frame relay on Cisco routers
8.5 Implement and troubleshoot PPPoE

Posted on 三月 21, 2015 by admin

010-151 DCTECH Cisco Certified Technician (CCT) for Data Center

Cisco Certified Technician (CCT) for Data Center is the full name of 010-151 DCTECH exam. The Associated Certifications is CCT Data Center. There are 65-75 questions in real Cisco 010-151 DCTECH exam, which will take the candidates 90 minutes to complete the test. The available language is English. Candidates can register Cisco 010-151 DCTECH exam at Pearson VUE testing center.

The Cisco Certified Technician (CCT) for Data Center validates a technician’s competency in the following areas; basic Cisco NX-OS configuration, Cisco Data Center products and hardware components with an emphasis on the Cisco Unified Computing System (UCS).

Cisco 010-151 DCTECH Free Online Test

Cisco 010-151 DCTECH exam objectives are important in your preparation.

17% 1.0 General Networking Knowledge

1.1 Demonstrate a high level understanding of SAN technology
1.2 Describe what an IP address and subnet is. Add default gateway and subnet mask
1.3 Differentiate between these Layer 2 technologies: Ethernet, Fast Ethernet, Gigabit Ethernet
1.4 Describe what FTP does
1.5 Describe what TFTP does
1.6 Describe what Telnet does
1.7 Describe what ping does
1.8 Use the OSI and TCP/IP models and their associated protocols to explain how data flows in a network
1.9 Identify and correct common network problems at Layers 1 and 2
1.10 Identify the cabling and connectors

25% 2.0 Identify Cisco Equipment and Related Hardware

2.1 Describe the Cisco Unified Computing System components and chassis layout
2.2 Describe the Cisco Unified Computing System LED
2.3 Describe the UCS C-series rack mount servers components and chassis layout
2.4 Describe the Cisco Nexus 2000 series fabric extender components
2.5 Identify Cisco Nexus 2000 series fabric extender cabling types
2.6 Describe the Cisco Nexus 5000 series switch components
2.7 Describe the Cisco Nexus 7000 series switch components
2.8 Describe the Cisco MDS 9000 product family components
2.9 Identifying the MDS 9000 Family Storage networking modules
2.10 Identify Cisco products by logo marking and model number (including, but not limited to locations on chassis, line card, module, or adapter)
2.11 Identify and locate the serial number of Cisco products (including but not limited to locations on chassis, line card, module, or adapter)

25% 3.0 Describe Cisco NX-OS Software Operation

3.1 Describe the Cisco Integrated Management Controller (CIMC)
3.2 Describe features and functionality of UCS Manager
3.3 Describe the different command modes for Cisco NX-OS software
3.4 Determine the current mode of the device
3.5 Know how to export technical support data
3.6 Verify the device configuration
3.7 Know how to use and interpret the basic Cisco NX-OS commands
3.8 Identify a configuration file from a Cisco device
3.9 Using the device file systems, directories, and files
3.10 Perform password recovery on a Cisco NX-OS switch device

33% 4.0 Service-Related Knowledge

4.1 Make a physical connection from laptop to Cisco console port
4.2 Perform installation process steps and expected outcomes
4.3 Perform initial setup tasks
4.4 Service restoration verification
4.5 Perform remedial procedures on Cisco devices
4.6 Use the hardware tools needed for repair
4.7 Upgrade the BIOS on a UCS Server Blade with the GUI
4.8 Upgrade Cisco Integrated Management Controller firmware on a UCS Server C-Series

Posted on 三月 20, 2015三月 20, 2015 by admin

100-101 ICND1 Interconnecting Cisco Networking Devices Part 1

The 100-101 Interconnecting Cisco Networking Devices Part 1 (ICND1) is the exam associated with the CCENT certification and a tangible first step in achieving the CCNA Routing and Switching certification. This 100-101 ICND1 exam tests a candidate’s knowledge and skills required to successfully install, operate, and troubleshoot a small branch office network.

In real Cisco 100-101 ICND1 exam, there are 45-55 questions, which will take the candidates 90 minutes to complete the test. The available languages are English and Japanese. Candidates can register Cisco 100-101 ICND1 exam at Pearson VUE testing center.

Cisco 100-101 ICND1 Free Online Test

Knowing Cisco 100-101 ICND1 exam topics is also important in your preparation.

1.0 Operation of IP Data Networks 6%

1.1 Recognize the purpose and functions of various network devices such as routers, switches, bridges and hubs
1.2 Select the components required to meet a given network specification
1.3 Identify common applications and their impact on the network
1.4 Describe the purpose and basic operation of the protocols in the OSI and TCP/IP models
1.5 Predict the data flow between two hosts across a network
1.6 Identify the appropriate media, cables, ports, and connectors to connect Cisco network devices to other network devices and hosts in a LAN

2.0 LAN Switching Technologies 21%

2.1 Determine the technology and media access control method for Ethernet networks
2.2 Identify basic switching concepts and the operation of Cisco switches
2.2.a Collision domains
2.2.b Broadcast domains
2.2.c Ways to switch
2.2.c [i] Store
2.2.c [ii] Forward
2.2.c [iii] Cut through
2.2.c [iv] CAM Table
2.3 Configure and verify initial switch configuration including remote access management
2.3.a hostname
2.3.b mgmt ip address
2.3.c Ip default-gateway
2.3.d local user and password
2.3.e enable secret password
2.3.f console and VTY logins
2.3.g exec-timeout
2.3.h service password encryption
2.3.i copy run start
2.4 Verify network status and switch operation using basic utilities such as
2.4.a ping
2.4.b telnet
2.4.c SSH
2.5 Describe how VLANs create logically separate networks and the need for routing between them
2.5.a Explain network segmentation and basic traffic management concepts
2.6 Configure and verify VLANs
2.7 Configure and verify trunking on Cisco switches
2.7.a DTP (topic)
2.7.b Auto-negotiation

3.0 IP addressing (IPv4/IPv6) 11%

3.1 Describe the operation and necessity of using private and public IP addresses for IPv4 addressing
3.2 Identify the appropriate IPv6 addressing scheme to satisfy addressing requirements in a LAN/WAN environment
3.3 Identify the appropriate IPv4 addressing scheme using VLSM and summarization to satisfy addressing requirements in a LAN/WAN environment
3.4 Describe the technological requirements for running IPv6 in conjunction with IPv4
3.4.a Dual stack
3.5 Describe IPv6 addresses
3.5.a Global unicast
3.5.b Multicast
3.5.c Link local
3.5.d Unique local
3.5.e EUI 64
3.5.f Auto-configuration

4.0 IP Routing Technologies 26%

4.1 Describe basic routing concepts
4.1.a Packet forwarding
4.1.b Router lookup process
4.1.c Process Switching/Fast Switching/CEF
4.2 Configure and verify utilizing the CLI to set basic Router configuration
4.2.a Hostname
4.2.b Local user & password
4.2.c Enable secret password
4.2.d Console & VTY logins
4.2.e exec-timeout
4.2.f service password encryption
4.2.g Interface IP Address
4.2.g [i] loopback
4.2.h banner
4.2.i motd
4.2.j copy run start
4.3 Configure and verify operation status of an Ethernet interface
4.4 Verify router configuration and network connectivity using
4.4.a ping
4.4.a [i] Extended ping
4.4.b traceroute
4.4.c telnet
4.4.d SSH
4.4.e Show cdp neighbors
4.5 Configure and verify routing configuration for a static or default route given specific routing requirements
4.6 Differentiate methods of routing and routing protocols
4.6.a Static vs. dynamic
4.6.b Link state vs. distance vector
4.6.c Next hop
4.6.d Ip routing table
4.6.e Passive interfaces (how they work)
4.7 Configure and verify OSPF (single area)
4.7.a Benefit of single area
4.7.b Configure OSPv2 in a single area
4.7.c Configure OSPv3 in a single area
4.7.d Router ID
4.7.e Passive interface
4.8 Configure and verify interVLAN routing (router on a stick)
4.8.a Sub interfaces
4.8.b Upstream routing
4.8.c Encapsulation
4.9 Configure SVI interfaces.

5.0 IP Services 8%

5.1 Configure and verify DHCP (IOS router)
5.1.a Configuring router interfaces to use DHCP
5.1.b DHCP options (Basic overview and functionality)
5.1.c Excluded addresses
5.1.d Lease time
5.2 Describe the types, features, and applications of ACLs
5.2.a Standard (editing and sequence numbers)
5.2.b Extended
5.2.c Named
5.2.d Numbered
5.2.e Log option
5.3 Configure and verify ACLs in a network environment
5.3.a Named
5.3.b Numbered
5.3.c Log option
5.4 Identify the basic operation of NAT
5.4.a Purpose
5.4.b Pool
5.4.c Static
5.4.d 1 to 1
5.4.e Overloading
5.4.f Source addressing
5.4.g One-way NAT
5.5 Configure and verify NAT for given network requirements
5.6 Configure and verify NTP as a client

6.0 Network Device Security 15%

6.1 Configure and verify network device security features
6.1.a Device password security
6.1.b Enable secret vs. enable
6.1.c Transport
6.1.c [i] Disable telnet
6.1.c [ii] SSH
6.1.d VTYs
6.1.e Physical security
6.1.f Service password
6.1.g Describe external authentication methods
6.2 Configure and verify switch port security
6.2.a Sticky mac
6.2.b MAC address limitation
6.2.c Static/dynamic
6.2.d Violation modes
6.2.d [i] Err disable
6.2.d [ii] Shutdown
6.2.d [iii] Protect restrict
6.2.e Shutdown unused ports
6.2.f Err disable recovery
6.2.g Assign unused ports in unused VLANs
6.2.h Putting Native VLAN to other than VLAN 1
6.3 Configure and verify ACLs to filter network traffic
6.4 Configure and verify ACLs to limit telnet and SSH access to the router

7.0 Troubleshooting 13%