200-401 IMINS Online Test-Managing Industrial Networks with Cisco Networking Technologies

Currently, our 200-401 IMINS online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used?

hop count

administrative distance

link bandwidth

link delay

link cost

With a Cisco IE 2000 switch, what does a power status LED indicate when it is solid green?

Power is present on the associated circuit and the system is operating normally.

Power is present on the associated circuit, but there is no correlation to whether the system is operating normally.

The system is operating normally, but power is not necessarily present on the associated circuit.

Power is not present on the associated circuit and the power supply alarm is configured.

The power status LED does not show solid green.

What is the purpose of a time domain reflectometer?

It uses pulses to locate and test for sheath faults, damaged conductors, loose connectors, splices, bridge taps, split pairs, and other problems.

It opens shorts and pinholes in cable shielding.

It correlates the returned light pulses with a location in the fiber.

It opens kinks and mismatched cable connectors.

How does the optical time domain reflectometer use “backscattered” light to make measurements?

It uses pulses to locate and test for sheath faults, damaged conductors, loose connectors, splices, bridge taps, split pairs, and other problems.

It performs wiremapping to measure that all pins are correctly connected.

It correlates the returned light pulses with a location in the fiber.

It measures light-pulse width to measure that all pins are correctly connected.

Which two commands can help you to determine what image is running on your industrial switch? (Choose two.)

show version

show spanning-tree

show interface-switch

show interfaces gigabitEthernet x/y switchport

show license

Which protocol is a secure alternative to Telnet?

SSH

FTP

SMTP

SNMP

HTTP

Which two reasons make mesh bonding systems most effective? (Choose two.)

cover wide areas

provide additional strength to floor structures

provide low-impedance noise-equalizing paths

create equipotential grounding systems

most cost-effective approach

What do deflections indicate to the time domain reflectometer user?

They indicate splices, water in the cable, split pairs, and discontinuities or faults.

Do not connect live circuit cables to the input of the time domain reflectometer. Connect the cable that is being tested to the cable connector on the front panel of the time domain reflectometer.

Upward deflections indicate high-impedance mismatches or opens, and downward deflections indicate shorts or low-impedance mismatches.

They are used to select the I/O impedance of the time domain reflectometer. You can select 50, 75, 95, or 125? impedances.

What are two benefits that are provided by proper grounding and bonding systems? (Choose two.)

higher speed communications

safe discharge of electrostatic energy

lower equipment power consumption

equipotential termination points for equipment and cable shields

lowest carbon footprint

Which three pieces of information must be maintained for all stakeholders as part of the change management process? (Choose three.)

the location of the person who applied the change

the date and time that the change was applied and on which device

the original change request form that indicates why the change is necessary

the size of the change (in bytes)

a description of the actual change itself (configuration, program code, and so on)

the names of the current members of the change advisory board

the industrial protocol that is used

Loading …

Question 1 of 10

admin Posted in CCNP free test on line 200-401 IMINS online test, and/or Remove an End-Device, and/or Remove an Infrastructure Device, and/or Remove Cables (network and/or power), Install, Maintain Appropriate End-Devices and Industrial Network Infrastructure Devices, Replace, Troubleshooting 2,010 views 3 Comments

CCNP Exams Test Base

New CCNP Exams from January 30, 2015

Note:

200-401 IMINS Online Test-Managing Industrial Networks with Cisco Networking Technologies

3 thoughts on “200-401 IMINS Online Test-Managing Industrial Networks with Cisco Networking Technologies”

Recent Posts

Tags

Links