Note:

  • CCIE Security 350-018 exam will be retired on January 30, 2017, the new exam is 400-251.
  • CCNA Data Center 640-911 DCICN exam will be retired on April 11, 2017.
  • CCNA Data Center 640-916 DCICT exam will be retired on April 11, 2017.
  • CCNP Data Center 642-035 DCUCT exam will be retired on July 3, 2017.
  • CCNP Data Center 642-980 DCUFT exam will be retired on July 3, 2017.
  • CCNP Data Center 642-996 DCUFD exam will be retired on July 3, 2017.
  • CCNP Data Center 642-997 DCUFI exam will be retired on July 3, 2017.
  • CCNP Data Center 642-998 DCUCD exam will be retired on July 3, 2017.
  • CCNP Data Center 642-999 DCUCI exam will be retired on July 3, 2017.
  • The new CCNP Data Center certification required exams are 300-180 DCIT, 300-165 DCII, 300-160 DCID, 300-175 DCUCI and 300-170 DCVAI exams.

Tag Archives: given a Network Design and a set of Requirements

05 Dec

cisco certification 642-902 route course

cisco certification 642-902 route course is here for the candidates to prepare the test. The Implementing Cisco IP Routing (ROUTE 642-902) is a qualifying exam for the Cisco Certified Network Professional CCNP, Cisco Certified Internetwork Professional CCIP, and Cisco Certified Design Professional CCDP certifications.

The cisco 642-902 ROUTE exam will certify that the successful candidate has the knowledge and skills necessary to use advanced IP addressing and routing in implementing scalable and secure Cisco ISR routers connected to LANs and WANs.

Below are the details of cisco 642-902 ROUTE exam objectives.

25% 1.0 Implement an EIGRP Based Solution, given a Network Design and a set of Requirements

1.1 Determine network resources needed for implementing EIGRP in a network
1.2 Create an EIGRP implementation plan
1.3 Create an EIGRP verification plan
1.4 Configure EIGRP routing
1.5 Verify EIGRP solution was implemented properly using show and debug commands
1.6 Document the results of EIGRP implementation and verification

25% 2.0 Implement a Multi-Area OSPF Network, given a Network Design and a set of Requirements

2.1 Determine network resources needed for implementing OSPF on a network
2.2 Create an OSPF implementation plan
2.3 Create an OSPF verification plan
2.4 Configure OSPF routing
2.5 Verify OSPF solution was implemented properly using show and debug commands
2.6 Document results of OSPF implementation and verification plan

cisco certification 642-902 route course online practice here. 

 

 

04 Dec

ccnp 642-813 switch exam preparation

ccnp 642-813 switch exam preparation is available, which is helpful for the candidates to prepare the test well. Implementing Cisco IP Switched Networks (SWITCH 642-813) is a qualifying exam for the Cisco Certified Network Professional CCNP, and Cisco Certified Design Professional CCDP certifications.

The SWITCH 642-813 exam will certify that the successful candidate has important knowledge and skills necessary to to plan, configure and verify the implementation of complex enterprise switching solutions using Cisco’s Campus Enterprise Architecture. Cisco 642-813 SWITCH exam objectives are as follows.

12% 2.0 Implement a Security Extension of a Layer 2 Solution, given a Network Design and a set of Requirements

2.1 Determine network resources needed for implementing a security solution
2.2 Create a implementation plan for the security solution
2.3 Create a verification plan for the security solution
2.4 Configure port security features
2.5 Configure general switch security features
2.6 Configure private VLANs
2.7 Configure VACL and PACL
2.8 Verify the Security based solution was implemented properly using show and debug commands
2.9 Document results of security implementation and verification

14% 3.0 Implement Switch Based Layer 3 Services, given a Network Design and a set of Requirements

3.1 Determine network resources needed for implementing a Switch based Layer 3 solution
3.2 Create an implementation plan for the Switch based Layer 3 solution
3.3 Create a verification plan for the Switch based Layer 3 solution
3.4 Configure routing interfaces
3.5 Configure Layer 3 Security
3.6 Verify the Switch based Layer 3 solution was implemented properly using show and debug commands
3.7 Document results of Switch based Layer 3 implementation and verification

Practice ccnp 642-813 switch exam preparation online here.

 

 

05 Aug

642-902 ROUTE Online Test-Implementing cisco ip routing

Currently, our 642-902 ROUTE online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

During BGP configuration on a router that has peered with other BGP speakers, the BGP command aggregate-address 172.32.0.0 255.255.252.0 is issued. However, the peers do not receive this aggregate network in BGP advertisements. Also, the router does not have this aggregate network in its BGP table. Which option indicates a possible reason this command did not cause the router to advertise the aggregate network to its peers?

 
 
 
 
 
 

What two situations could require the use of multiple routing protocols? (Choose two)

 
 
 
 
 
 

Using the rules for IPv6 addressing, how can the address 2031:0000:240F:0000:0000:09C0:123A:121B be rewritten?

 
 
 
 

How is authentication handled with OSPFv3?

 
 
 
 

A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight and local preference values. Which statement is true about how BGP would select the best path?

 
 
 
 

What is the difference between the IPv6 addresses ::/0 and ::/128?

 
 
 
 
 
 

What are two rules for compacting IPv6 addresses? (Choose two.)

 
 
 
 
 
 

What are the two reasons for the appearance of 0.0.0.0 as the next hop for a network in the show ip bgp command output? (Choose two.)

 
 
 
 
 

Which three restrictions apply to OSPF stub areas? (Choose three.)

 
 
 
 
 
 

Into which two types of areas would an area border router (ABR) inject a default route.? (Choose two.)

 
 
 
 
 
 

Question 1 of 10

 

cart

 

 

 

 

 

 

 

05 Aug

642-813 SWITCH Online Test-Implementing Cisco IP Switched Networks

Currently, our 642-813 SWITCH online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

Please go to 642-813 SWITCH Online Test-Implementing Cisco IP Switched Networks to view the test

 

 

cart

 

04 Aug

642-813 SWITCH Implementing Cisco IP Switched Networks

Implementing Cisco IP Switched Networks (SWITCH 642-813) is a qualifying exam for the Cisco Certified Network Professional CCNP, and Cisco Certified Design Professional CCDP certifications. The SWITCH 642-813 exam will certify that the successful candidate has important knowledge and skills necessary to to plan, configure and verify the implementation of complex enterprise switching solutions using Cisco’s Campus Enterprise Architecture.

642-813 SWITCH is known as Implementing Cisco IP Switched Networks. The Associated Certifications are CCDP, CCNP Routing and Switching. There are 35-45 questions in real 642-813 SWITCH test, which will take the candidates 120 minutes to complete the test. The available language is English. Candidates can register 642-813 SWITCH exam at Pearson VUE testing center.

642-813 SWITCH exam objectives are also helpful in your preparation.

50% 1.0 Implement VLAN Based Solution, given a Network Design and a set of Requirements

1.1 Determine network resources needed for implementing a VLAN based solution on a network
1.2 Create a VLAN based implementation plan
1.3 Create a VLAN based verification plan
1.4 Configure switch-to-switch connectivity for the VLAN based solution
1.5 Configure loop prevention for the VLAN based solution
1.6 Verify EIGRP solution was implemented properly using show and debug commands

12% 2.0 Implement a Security Extension of a Layer 2 Solution, given a Network Design and a set of Requirements

2.1 Determine network resources needed for implementing a security solution
2.2 Create a implementation plan for the security solution
2.3 Create a verification plan for the security solution
2.4 Configure port security features
2.5 Configure general switch security features
2.6 Configure private VLANs
2.7 Configure VACL and PACL
2.8 Verify the Security based solution was implemented properly using show and debug commands
2.9 Document results of security implementation and verification

14% 3.0 Implement Switch Based Layer 3 Services, given a Network Design and a set of Requirements

3.1 Determine network resources needed for implementing a Switch based Layer 3 solution
3.2 Create an implementation plan for the Switch based Layer 3 solution
3.3 Create a verification plan for the Switch based Layer 3 solution
3.4 Configure routing interfaces
3.5 Configure Layer 3 Security
3.6 Verify the Switch based Layer 3 solution was implemented properly using show and debug commands
3.7 Document results of Switch based Layer 3 implementation and verification

5% 4.0 Prepare infrastructure to Support Advanced Services

4.1 Implement a Wireless Extension of a Layer 2 solutio
4.2 Implement a VoIP support solution
4.3 Implement video support solution

19% 5.0 Implement High Availability, given a Network Design and a set of Requirements

5.1 Determine network resources needed for implementing High Availability on a network
5.2 Create a High Availability implementation plan
5.3 Create a High Availability verification plan
5.4 Implement first hop redundancy protocols
5.5 Implement switch supervisor redundancy
5.6 Verify High Availability solution was implemented properly using show and debug commands
5.7 Document results of High Availability implementation and verification

Exam Note: The latest day of 642-813 SWITCH to test is January 29, 2015. The new exam is 300-115 SWITCH, which begins January 30, 2015.

Related resource: http://www.cisco.com/web/learning/exams/list/switch.html#~Topics

04 Aug

642-902 ROUTE Implementing Cisco IP Routing

The Implementing Cisco IP Routing (ROUTE 642-902) is a qualifying exam for the Cisco Certified Network Professional CCNP, Cisco Certified Internetwork Professional CCIP, and Cisco Certified Design Professional CCDP certifications. The exam will certify that the successful candidate has the knowledge and skills necessary to use advanced IP addressing and routing in implementing scalable and secure Cisco ISR routers connected to LANs and WANs.

Implementing Cisco IP Routing is the full name of 642-902 ROUTE. The Associated Certifications are CCDP and CCNP Routing and Switching. There are 45-55 questions in real 642-902 ROUTE exam, which will take the candidates 120 minutes to complete the test. The available languages are English and japanese. Candidates can register 642-902 ROUTE exam at Pearson VUE testing center.

It is also important for the candidates to know 642-902 ROUTE exam topics before taking the test.
25% 1.0 Implement an EIGRP Based Solution, given a Network Design and a set of Requirements
1.1 Determine network resources needed for implementing EIGRP in a network
1.2 Create an EIGRP implementation plan
1.3 Create an EIGRP verification plan
1.4 Configure EIGRP routing
1.5 Verify EIGRP solution was implemented properly using show and debug commands
1.6 Document the results of EIGRP implementation and verification

25% 2.0 Implement a Multi-Area OSPF Network, given a Network Design and a set of Requirements

2.1 Determine network resources needed for implementing OSPF on a network
2.2 Create an OSPF implementation plan
2.3 Create an OSPF verification plan
2.4 Configure OSPF routing
2.5 Verify OSPF solution was implemented properly using show and debug commands
2.6 Document results of OSPF implementation and verification plan

5% 3.0 Implement an eBGP Based Solution, given a Network Design and a set of Requirements

3.1 Determine network resources needed for implementing eBGP on a network
3.2 Create an eBGP implementation plan
3.3 Create an eBGP verification plan
3.4 Configure eBGP routing
3.5 Verify eBGP solution was implemented properly using show and debug commands
3.6 Document results of eBGP implementation and verification plan

15% 4.0 Implement an IPv6 Based Solution, given a Network Design and a set of Requirements

4.1 Determine network resources needed for implementing IPv6 on a network
4.2 Create an IPv6 implementation plan
4.3 Create an IPv6 verification plan
4.4 Configure IPv6 routing
4.5 Configure IPv6 interoperation with IPv4
4.6 Verify IPv6 solution was implemented properly using show and debug commands
4.7 Document results of IPv6 implementation and verification plan

15% 5.0 Implement an IPv4 or IPv6 Based Redistribution Solution, given a Network Design and a set of Requirements

5.1 Create a redistribution implementation plan based upon the results from a redistribution analysis
5.2 Create a redistribution verification plan
5.3 Configure a redistribution solution
5.4 Verify that a redistribution was implemented
5.5 Document results of a redistribution implementation and verification plan
5.6 Identify the differences between implementing an IPv4 and IPv6 redistribution solution

10% 6.0 Implement Layer 3 Path Control Solution

6.1 Create a Layer 3 path control implementation plan based upon the results of the redistribution analysis
6.2 Create a Layer 3 path control verification pla
6.3 Configure Layer 3 path control
6.4 Verify that a Layer 3 path control was implemented
6.5 Document results of a Layer 3 path control implementation and verification plan

5% 7.0 Implement Basic Teleworker and Branch Services

7.1 Describe broadband technologies
7.2 Configure basic broadband connections
7.3 Describe basic VPN technologies
7.4 Configure GRE
7.5 Describe branch access technologies

Exam Note: The latest day of 642-902 ROUTE to test is January 29, 2015. The new exam is 300-101 ROUTE, which begins January 30, 2015.

Related resource: http://www.cisco.com/web/learning/exams/list/route.html#~Topics,


Recent Posts


Tags

and/or Remove an End-Device and/or Remove an Infrastructure Device and/or Remove Cables (network and/or power) Cisco 642-997 DCUFI exam Cisco 642-999 DCUCI exam Configure Cisco Unity Connection Configure Cisco Unity Express using the GUI Describe and implement centralized call processing redundancy Describe Data Center Structure and Modularity Describe the Design Methodology Describe the Technologies used within the Data Center Describe WLAN Fundamentals Design and Deploy WLAN Infrastructure for Mobility Design Network Management Considerations into a Data Center Design the Access Layer of a Data Center General Networking Knowledge given a Network Design and a set of Requirements High Availability Routing Features Identify Cisco Equipment and Related Hardware Implement high availability features on Cisco Unified Fabric products in a Cisco Data Center Architecture Implement Multicast over Wireless Implement QoS for Wireless Applications Implement VoWLAN Infrastructure Security Infrastructure Services Install Integrate Client Device Security IP Services LAN Switching Technologies Layer 2 Technologies Layer 3 Technologies Maintain Appropriate End-Devices and Industrial Network Infrastructure Devices Manage the Unified Fabric in a Cisco Data Center Architecture Monitoring and Reporting Tools Network Principles Replace Service-Related Knowledge Threat Defense Threat Defense Architectures Troubleshoot Call Setup Issues Troubleshooting Troubleshoot Registration Issues UCS Compute Troubleshooting VPN Technologies WAN Technologies

Links

Powered by CCNP Exams Test Base