Note:

  • The new CCNP Data Center certification required exams are 300-180 DCIT, 300-165 DCII, 300-160 DCID, 300-175 DCUCI and 300-170 DCVAI exams.
  • The last day to test Cisco 810-403 OUTCOMES exam is December 29, 2017.
  • The last day to test Cisco 820-424 BTASBVA exam is December 29, 2017.

Tag Archives: 300-101 ROUTE online test

17 Oct

Cisco 300-101 ROUTE Online Test

Currently, our 300-101 ROUTE online test only provide 20 questions. Answer one question correctly, you can get 5 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

When using SNMPv3 with NoAuthNoPriv, which string is matched for authentication?

 
 
 
 

After a recent DoS attack on a network, senior management asks you to implement better logging functionality on all IOS-based devices. Which two actions can you take to provide enhanced logging results? (Choose two.)

 
 
 
 
 

A network engineer finds that a core router has crashed without warning. In this situation, which feature can the engineer use to create a crash collection?

 
 
 
 
 

A network engineer is trying to implement broadcast-based NTP in a network and executes the ntp broadcast client command. Assuming that an NTP server is already set up, what is the result of the command?

 
 
 
 

What is a function of NPTv6?

 
 
 
 

IPv6 has just been deployed to all of the hosts within a network, but not to the servers. Which feature allows IPv6 devices to communicate with IPv4 servers?

 
 
 
 
 

A network engineer initiates the ip sla responder tcp-connect command in order to gather statistics for performance gauging. Which type of statistics does the engineer see?

 
 
 
 

A network engineer executes the “ipv6 flowset” command. What is the result?

 
 
 
 

A network engineer executes the show ip flow export command. Which line in the output indicates that the send queue is full and export packets are not being sent?

 
 
 
 

A network engineer is asked to configure a “site-to-site” IPsec VPN tunnel. One of the last things that the engineer does is to configure an access list (access-list 1 permit any) along with the command ip nat inside source list 1 int s0/0 overload. Which functions do the two commands serve in this scenario?

 
 
 
 

A network engineer is configuring a solution to allow failover of HSRP nodes during maintenance windows, as an alternative to powering down the active router and letting the network respond accordingly. Which action will allow for manual switching of HSRP nodes?

 
 
 
 

A network engineer is notified that several employees are experiencing network performance related issues, and bandwidth-intensive applications are identified as the root cause. In order to identify which specific type of traffic is causing this slowness, information such as the source/destination IP and Layer 4 port numbers is required. Which feature should the engineer use to gather the required information?

 
 
 
 
 

An organization decides to implement NetFlow on its network to monitor the fluctuation of traffic that is disrupting core services. After reviewing the output of NetFlow, the network engineer is unable to see OUT traffic on the interfaces. What can you determine based on this information?

 
 
 
 

A network engineer has left a NetFlow capture enabled over the weekend to gather information regarding excessive bandwidth utilization. The following command is entered:
switch#show flow exporter Flow_Exporter-1
What is the expected output?

 
 
 
 

A company’s corporate policy has been updated to require that stateless, 1-to-1, and IPv6 to IPv6 translations at the Internet edge are performed. What is the best solution to ensure compliance with this new policy?

 
 
 
 
 

Which two functions are completely independent when implementing NAT64 over NAT-PT? (Choose two.)

 
 
 
 
 

Which two methods of deployment can you use when implementing NAT64? (Choose two.)

 
 
 
 
 
 
 

Which NetFlow component is applied to an interface and collects information about flows?

 
 
 
 

Refer to the exhibit.
Which statement about the output of the show flow-sampler command is true?

 
 
 
 

What is the result of the command ip flow-export destination 10.10.10.1 5858?

 
 
 
 

Question 1 of 20

cart


Recent Posts


Tags

and/or Remove an End-Device and/or Remove an Infrastructure Device and/or Remove Cables (network and/or power) Cisco 642-997 DCUFI exam Cisco 642-999 DCUCI exam Configure Cisco Unity Connection Configure Cisco Unity Express using the GUI Describe and implement centralized call processing redundancy Describe Data Center Structure and Modularity Describe the Design Methodology Describe the Technologies used within the Data Center Describe WLAN Fundamentals Design and Deploy WLAN Infrastructure for Mobility Design Network Management Considerations into a Data Center Design the Access Layer of a Data Center General Networking Knowledge given a Network Design and a set of Requirements High Availability Routing Features Identify Cisco Equipment and Related Hardware Implement high availability features on Cisco Unified Fabric products in a Cisco Data Center Architecture Implement Multicast over Wireless Implement QoS for Wireless Applications Implement VoWLAN Infrastructure Security Infrastructure Services Install Integrate Client Device Security IP Services LAN Switching Technologies Layer 2 Technologies Layer 3 Technologies Maintain Appropriate End-Devices and Industrial Network Infrastructure Devices Manage the Unified Fabric in a Cisco Data Center Architecture Monitoring and Reporting Tools Network Principles Replace Service-Related Knowledge Threat Defense Threat Defense Architectures Troubleshoot Call Setup Issues Troubleshooting Troubleshoot Registration Issues UCS Compute Troubleshooting VPN Technologies WAN Technologies

Links

Powered by CCNP Exams Test Base