Note:

  • CCIE Security 350-018 exam will be retired on January 30, 2017, the new exam is 400-251.
  • CCNA Data Center 640-911 DCICN exam will be retired on April 11, 2017.
  • CCNA Data Center 640-916 DCICT exam will be retired on April 11, 2017.
  • CCNP Data Center 642-035 DCUCT exam will be retired on July 3, 2017.
  • CCNP Data Center 642-980 DCUFT exam will be retired on July 3, 2017.
  • CCNP Data Center 642-996 DCUFD exam will be retired on July 3, 2017.
  • CCNP Data Center 642-997 DCUFI exam will be retired on July 3, 2017.
  • CCNP Data Center 642-998 DCUCD exam will be retired on July 3, 2017.
  • CCNP Data Center 642-999 DCUCI exam will be retired on July 3, 2017.
  • The new CCNP Data Center certification required exams are 300-180 DCIT, 300-165 DCII, 300-160 DCID, 300-175 DCUCI and 300-170 DCVAI exams.

Category Archives: CCNP Routing and Switching

27 Apr

Cisco 300-115 Real Exam Questions

The certification of Cisco 300-115 more and more valuable in the IT area and a lot people use the products of ccnp2015 blog to pass Cisco certification 300-115 exam. Through so many feedbacks of these products, our ccnp2015 blog Cisco 300-115 Real Exam Questions prove to be trusted.You can first download ccnp2015 blog Cisco 300-115 Real Exam Questions as a try, then you will feel that ccnp2015 blog give you a reassurance for passing the exam.

Cisco 300-115 Free Online Test Share

If you choose ccnp2015 blog to provide you with the pertinence training, you can easily pass the Cisco certification 300-115 exam.Cisco 300-115 exam certification is widely recognized IT certifications. People around the world prefer 300-115 exam certification to make their careers more strengthened and successful. Speaking of Cisco 300-115 exam, ccnp2015 blog Cisco 300-115 Real Exam Questions have been ahead of other sites.

With ccnp2015 blog Cisco 300-115 Real Dumps, you can be brimming with confidence, and do not need to worry the exam. Of course, you can also face the exam with ease. This is not only psychological help, but more importantly, it allows you to pass the exam and to help you get a better tomorrow. ccnp2015 blog is a very good website for Cisco certification 300-115 exams to provide convenience.

According to the research of the past exam exercises and answers, ccnp2015 blog can effectively capture the content of Cisco certification 300-115 exam. ccnp2015 blog Cisco 300-115 Real Dumps have a very close similarity with real examination exercises.Perhaps you have also seen the related Cisco 300-115 Real Dumps on other websites, but our ccnp2015 blog has a pivotal position in the field of IT certification exam.

So ccnp2015 blog a website worthy of your trust. Please select ccnp2015 blog, you will be the next successful IT person. ccnp2015 blog will help you achieve your dream.ccnp2015 blog is website that can help a lot of IT people realize their dreams. If you have a IT dream,then quickly click the click of ccnp2015 blog. It has the best training materials, which is ccnp2015 blog Cisco 300-115 Actual Questions.

24 Apr

Cisco CCNP Routing and Switching 300-101 Exam

To be sure, ccnp2015 blog Cisco CCNP Routing and Switching 300-101 Exam can provide you with the most practical IT certification material.ccnp2015 blog provide training tools included Cisco certification 300-101 exam study materials and simulation training questions and more importantly, we will provide you Cisco CCNP Routing and Switching 300-101 Exam which are very close with real certification exam. Selecting ccnp2015 blog can guarantee that you can in a short period of time to learn and to strengthen the professional knowledge of IT and pass Cisco certification 300-101 exam with high score.

Cisco CCNP Routing and Switching 300-101 Exam Online Test Share

Our latest Cisco CCNP Routing and Switching 300-101 Exam is developed by ccnp2015 blog professional team’s constantly study the outline. It can help a lot of people achieve their dream. In today’s competitive IT profession, if you want to stabilize your own position, you will have to prove your professional knowledge and technology level. Cisco certification 300-101 exam is a very good test to prove your ability.

Although there are many ways to help you achieve your purpose, selecting ccnp2015 blog is your wisest choice. Having ccnp2015 blog can make you spend shorter time less money and with greater confidence to pass the exam, and we also provide you with a free one-year after-sales service.ccnp2015 blog Cisco CCNP Routing and Switching 300-101 Exam are made in accordance with the latest syllabus and the actual Cisco 300-101 certification exam.

We constantly upgrade our Cisco CCNP Routing and Switching 300-101 Exam, all the products you get with one year of free updates. You can always extend the to update subscription time, so that you will get more time to fully prepare for the exam. If you still confused to use the Cisco CCNP Routing and Switching 300-101 Exam of ccnp2015 blog, then you can download part of the examination questions and answers in ccnp2015 blog website. It is free to try, and if it is suitable for you, then go to buy it, to ensure that you will never regret.

Select the appropriate shortcut just to guarantee success. The ccnp2015 blog exists precisely to your success. Select ccnp2015 blog is equivalent to choose success. The Cisco CCNP Routing and Switching 300-101 Exam provided by ccnp2015 blog is obtained through the study and practice of ccnp2015 blog IT elite. The material has the experience of more than 10 years of IT certification. In fact, you can take steps to pass the certification. ccnp2015 blog Cisco CCNP Routing and Switching 300-101 Exam bear with a large number of the exam questions you need, which is a good choice.

10 Dec

ccnp 300-135 tshoot tutorial

ccnp 300-135 tshoot tutorial is available. Share some 300-135 tshoot questions and answers below.

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolate the cause of this fault and answer the following question.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: D

ccnp 300-135 tshoot tutorial, 300-135 tshoot questions and answers, 300-135 tshoot exam

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolate the cause of this fault and answer the following question. The fault condition is related to which technology?
A. NTP
B. IP DHCP Server
C. Ipv4 OSPF Routing
D. Ipv4 EIGRP Routing.
E. Ipv4 Route Redistribution.
F. Ipv6 RIP Routing
G. Ipv6 OSPF Routing
H. Ipv4 and Ipv6 Interoperability
I. Ipv4 layer 3 security.
Answer: B

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolate the cause of this fault and answer the following question. What is the solution to the fault condition?
A. Under the global configuration, delete the no ip dhcp use vrf connected command.
B. Under the IP DHCP pool configuration, delete the default -router 10.2.1.254 command and enter the default-router 10.1.4.5 command.
C. Under the IP DHCP pool configuration, delete the network 10.2.1.0 255.255.255.0 command and enter the network 10.1.4.0 255.255.255.0 command.
D. Under the IP DHCP pool configuration, issue the no ip dhcp excluded-address 10.2.1.1 10.2.1.253 command and enter the ip dhcp excluded-address 10.2.1.1 10.2.1.2 command.
Answer: D

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10. Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: E

 

cart

 

 

09 Dec

ccnp routing and switching 300-135 tshoot dumps

ccnp routing and switching 300-135 tshoot dumps are available. It is helpful for the candidates to practice them.

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10. Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: E

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10. Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?
A. NTP
B. HSRP
C. IP DHCP Helper
D. IPv4 EIGRP Routing
E. IPv6 RIP Routing
F. IPv4 layer 3 security
G. Switch-to-Switch Connectivity
H. Loop Prevention
I. Access Vlans
Answer: B

ccnp routing and switching 300-135 tshoot dumps, 300-135 tshoot exam, 300-135 test

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10. Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?
A. Under the interface vlan 10 configuration enter standby 10 preempt command.
B. Under the track 1 object configuration delete the threshold metric up 1 down 2 command and enter the threshold metric up 61 down 62 command.
C. Under the track 10 object configuration delete the threshold metric up 61 down 62 command and enter the threshold metric up 1 down 2 command.
D. Under the interface vlan 10 configuration delete the standby 10 track1 decrement 60 command and enter the standby 10 track 10 decrement 60 command.
Answer: D

The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolate the cause of this fault and answer the following question. On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: D

 

cart

 

06 Dec

cisco 300-101 route training program

cisco 300-101 route training program is available for the candidates to prepare the test. Share some 300-101 route questions and answers below.

Which three conditions can cause BGP neighbor establishment to fail? (Select three)
A. There is an access list blocking all TCP traffic between the two BGP neighbors.
B. The EBGP neighbor is not directly connected, and the ebgp-multi-hop option is set to the default valu
C. The IBGP neighbor is not directly connected.
D. BGP synchronization is enabled in a Transit AS with fully-meshed IBGP neighbors.
E. The BGP update interval is different between the two BGP neighbors.
F. The BGP neighbor is referencing an incorrect AS number in its neighbor statement.
Answer: A,B,F

cisco 300-101 route training program, 300-101 route exam, 300-101 route test

Which three of the statements below correctly describe the characteristics of Autonomous Systems in routed networks? (Select three)
A. Within an AS, all routers must run either BGP or IBGP.
B. An AS uses exterior gateway protocols (EGPs) to exchange information with other autonomous systems.
C. An AS is a group of routers under the same technical administration.
D. Within an AS, routes learned through BGP can be redistributed using interior gateway protocols.
E. Within an AS, routes learned through an interior protocol cannot be redistributed using BGP to other autonomous systems.
Answer: B,C,D

What are the two reasons for the appearance of 0.0.0.0 as the next hop for a network when using the “show ip bgp” command? (Choose two)
A. The network was originated via redistribution of an interior gateway protocol into BGP.
B. The network was defined by a static route.
C. The network was learned via IBGP.
D. The network was learned via EBGP.
E. The network was originated via a network or aggregate command.
Answer: A,E

What are two rules for compacting IPv6 addresses? (Choose two.)
A. Every 16-bit segment segment that consists of all zeroes can be represented with a single colon.
B. The trailing zeroes in any 16-bit segment do not have to be written.
C. The leading zeroes in any 16-bit segment do not have to be written.
D. Any single, continuous string of one or more 16-bit segments that consists of all zeroes can be represented with a double colon.
E. The maximum number of times a double colon can replace a 16-bit segment that consists of all zeroes is two.
F. Two zeroes in the middle of any 16-bit segment do not have to be written.
Answer: C,D

Practice cisco 300-101 route training program online here. 

 

 

05 Dec

cisco certification 642-902 route course

cisco certification 642-902 route course is here for the candidates to prepare the test. The Implementing Cisco IP Routing (ROUTE 642-902) is a qualifying exam for the Cisco Certified Network Professional CCNP, Cisco Certified Internetwork Professional CCIP, and Cisco Certified Design Professional CCDP certifications.

The cisco 642-902 ROUTE exam will certify that the successful candidate has the knowledge and skills necessary to use advanced IP addressing and routing in implementing scalable and secure Cisco ISR routers connected to LANs and WANs.

Below are the details of cisco 642-902 ROUTE exam objectives.

25% 1.0 Implement an EIGRP Based Solution, given a Network Design and a set of Requirements

1.1 Determine network resources needed for implementing EIGRP in a network
1.2 Create an EIGRP implementation plan
1.3 Create an EIGRP verification plan
1.4 Configure EIGRP routing
1.5 Verify EIGRP solution was implemented properly using show and debug commands
1.6 Document the results of EIGRP implementation and verification

25% 2.0 Implement a Multi-Area OSPF Network, given a Network Design and a set of Requirements

2.1 Determine network resources needed for implementing OSPF on a network
2.2 Create an OSPF implementation plan
2.3 Create an OSPF verification plan
2.4 Configure OSPF routing
2.5 Verify OSPF solution was implemented properly using show and debug commands
2.6 Document results of OSPF implementation and verification plan

cisco certification 642-902 route course online practice here. 

 

 

04 Dec

ccnp 642-813 switch exam preparation

ccnp 642-813 switch exam preparation is available, which is helpful for the candidates to prepare the test well. Implementing Cisco IP Switched Networks (SWITCH 642-813) is a qualifying exam for the Cisco Certified Network Professional CCNP, and Cisco Certified Design Professional CCDP certifications.

The SWITCH 642-813 exam will certify that the successful candidate has important knowledge and skills necessary to to plan, configure and verify the implementation of complex enterprise switching solutions using Cisco’s Campus Enterprise Architecture. Cisco 642-813 SWITCH exam objectives are as follows.

12% 2.0 Implement a Security Extension of a Layer 2 Solution, given a Network Design and a set of Requirements

2.1 Determine network resources needed for implementing a security solution
2.2 Create a implementation plan for the security solution
2.3 Create a verification plan for the security solution
2.4 Configure port security features
2.5 Configure general switch security features
2.6 Configure private VLANs
2.7 Configure VACL and PACL
2.8 Verify the Security based solution was implemented properly using show and debug commands
2.9 Document results of security implementation and verification

14% 3.0 Implement Switch Based Layer 3 Services, given a Network Design and a set of Requirements

3.1 Determine network resources needed for implementing a Switch based Layer 3 solution
3.2 Create an implementation plan for the Switch based Layer 3 solution
3.3 Create a verification plan for the Switch based Layer 3 solution
3.4 Configure routing interfaces
3.5 Configure Layer 3 Security
3.6 Verify the Switch based Layer 3 solution was implemented properly using show and debug commands
3.7 Document results of Switch based Layer 3 implementation and verification

Practice ccnp 642-813 switch exam preparation online here.

 

 

03 Dec

ccnp 642-832 tshoot practice questions

ccnp 642-832 tshoot practice questions are available. Troubleshooting and Maintaining Cisco IP Networks (TSHOOT 642-832) is a qualifying exam for the Cisco Certified Network Professional CCNP, certification.

The 642-832 TSHOOT exam will certify that the successful candidate has important knowledge and skills necessary to plan and perform regular maintenance on complex enterprise routed and switched networks and use technology-based practices and a systematic ITIL-compliant approach to perform network troubleshooting.

Below are the details of ccnp 642-832 tshoot practice questions objectives.

6% 1.0 Maintain and Monitor Network Performance

1.1 Develop a plan to monitor and manage a network
1.2 Perform network monitoring using IOS tools
1.3 Perform routine IOS device maintenance
1.4 Isolate sub-optimal internetwork operation at the correctly defined OSI Model layer

94% 2.0 Troubleshoot Multi Protocol System Networks

2.1 Troubleshoot EIGRP
2.2 Troubleshoot OSPF
2.3 Troubleshoot eBGP
2.4 Troubleshoot routing redistribution solution
2.5 Troubleshoot a DHCP client and server solution
2.6 Troubleshoot NAT
2.7 Troubleshoot first hop redundancy protocols
2.8 Troubleshoot IPv6 routing
2.9 Troubleshoot IPv6 and IPv4 interoperability
2.10 Troubleshoot switch-to-switch connectivity for the VLAN based solution
2.11 Troubleshoot loop prevention for the VLAN based solution
2.12 Troubleshoot Access Ports for the VLAN based solution

Practice ccnp 642-832 tshoot practice questions here. 

 

 

02 Dec

cisco certification 300-101 route books

cisco certification 300-101 route books are available. Implementing Cisco IP Routing (ROUTE 300-101) is a qualifying exam for the Cisco CCNP Routing and Switching and CCDP certifications. The ROUTE 300-101 exam certifies the routing knowledge and skills of successful candidates.

They are certified in using advanced IP addressing and routing in implementing scalable and highly secure Cisco routers that are connected to LANs, WANs, and IPv6. Below are the details of Cisco 300-101 Route exam objectives.

10% 5.0 Infrastructure Security

5.1 Describe IOS AAA using local database
5.2 Describe device security using IOS AAA with TACACS+ and RADIUS
5.2.a AA with TACACS+ and RADIUS
5.2.b Local privilege authorization fallback
5.3 Configure and verify device access control
5.3.a Lines (VTY, AUX, console)
5.3.b Management plane protection
5.3.c Password encryption
5.4 Configure and verify router security features
5.4.a IPv4 access control lists (standard, extended, time-based)
5.4.b IPv6 traffic filter
5.4.c Unicast reverse path forwarding

20% 6.0 Infrastructure Services

6.1 Configure and verify device management
6.1.a Console and VTY
6.1.b Telnet, HTTP, HTTPS, SSH, SCP
6.1.c (T)FTP
6.2 Configure and verify SNMP
6.2.a V2
6.2.b V3
6.3 Configure and verify logging
6.3.a Local logging, syslog, debugs, conditional debugs
6.3.b Timestamps
6.4 Configure and verify Network Time Protocol (NTP)
6.4.a NTP master, client, version 3, version 4
6.4.b NTP authentication
6.5 Configure and verify IPv4 and IPv6 DHCP
6.5.a DHCP client, IOS DHCP server, DHCP relay
6.5.b DHCP options (describe)
6.6 Configure and verify IPv4 Network Address Translation (NAT)
6.6.a Static NAT, dynamic NAT, PAT
6.7 Describe IPv6 NAT
6.7.a NAT64
6.7.b NPTv6
6.8 Describe SLA architecture
6.9 Configure and verify IP SLA
6.9.a ICMP
6.10 Configure and verify tracking objects
6.10.a Tracking objects
6.10.b Tracking different entities (for example, interfaces, IPSLA results)
6.11 Configure and verify Cisco NetFlow
6.11.a NetFlow v5, v9
6.11.b Local retrieval
6.11.c Export (configuration only)

Practice cisco certification 300-101 route books here. 

 

 

01 Dec

cisco certification 300-115 switch programs

cisco certification 300-115 switch programs are available now. Candidates can prepare the test well with this material.Implementing Cisco IP Switched Networks (SWITCH 300-115) is a qualifying exam for the Cisco CCNP Routing and Switching and CCDP certifications.

The SWITCH 300-115 exam certifies the switching knowledge and skills of successful candidates. They are certified in planning, configuring, and verifying the implementation of complex enterprise switching solutions that use the Cisco Enterprise Campus Architecture. Below are the details of Cisco 300-115 exam objectives.

65% 1.0 Layer 2 Technologies

1.1 Configure and verify switch administration
1.1.a SDM templates
1.1.b Managing MAC address table
1.1.c Troubleshoot Err-disable recovery
1.2 Configure and verify Layer 2 protocols
1.2.a CDP, LLDP
1.2.b 1.2.b UDLD
1.3 Configure and verify VLANs
1.3.a Access ports
1.3.b VLAN database
1.3.c Normal, extended VLAN, voice VLAN
1.4 Configure and verify trunking
1.4.a VTPv1, VTPv2, VTPv3, VTP pruning
1.4.b dot1Q
1.4.c Native VLAN
1.4.d Manual pruning
1.5 Configure and verify EtherChannels
1.5.a LACP, PAgP, manual
1.5.b Layer 2, Layer 3
1.5.c Load balancing
1.5.d EtherChannel misconfiguration guard
1.6 Configure and verify spanning tree
1.6.a PVST+, RPVST+, MST
1.6.b Switch priority, port priority, path cost, STP timers
1.6.c PortFast, BPDUguard, BPDUfilter
1.6.d Loopguard and Rootguard
1.7 Configure and verify other LAN switching technologies
1.7.a PAN, RSPAN
1.8 Describe chassis virtualization and aggregation technologies
1.8.a Stackwise

Practice cisco certification 300-115 switch programs here. 

 

 


Recent Posts


Tags

and/or Remove an End-Device and/or Remove an Infrastructure Device and/or Remove Cables (network and/or power) Cisco 642-997 DCUFI exam Cisco 642-999 DCUCI exam Configure Cisco Unity Connection Configure Cisco Unity Express using the GUI Describe and implement centralized call processing redundancy Describe Data Center Structure and Modularity Describe the Design Methodology Describe the Technologies used within the Data Center Describe WLAN Fundamentals Design and Deploy WLAN Infrastructure for Mobility Design Network Management Considerations into a Data Center Design the Access Layer of a Data Center General Networking Knowledge given a Network Design and a set of Requirements High Availability Routing Features Identify Cisco Equipment and Related Hardware Implement high availability features on Cisco Unified Fabric products in a Cisco Data Center Architecture Implement Multicast over Wireless Implement QoS for Wireless Applications Implement VoWLAN Infrastructure Security Infrastructure Services Install Integrate Client Device Security IP Services LAN Switching Technologies Layer 2 Technologies Layer 3 Technologies Maintain Appropriate End-Devices and Industrial Network Infrastructure Devices Manage the Unified Fabric in a Cisco Data Center Architecture Monitoring and Reporting Tools Network Principles Replace Service-Related Knowledge Threat Defense Threat Defense Architectures Troubleshoot Call Setup Issues Troubleshooting Troubleshoot Registration Issues UCS Compute Troubleshooting VPN Technologies WAN Technologies

Links

Powered by CCNP Exams Test Base