Note:

  • The new CCNP Data Center certification required exams are 300-180 DCIT, 300-165 DCII, 300-160 DCID, 300-175 DCUCI and 300-170 DCVAI exams.
  • The last day to test Cisco 810-403 OUTCOMES exam is December 29, 2017.
  • The last day to test Cisco 820-424 BTASBVA exam is December 29, 2017.
23 Mar

642-742 IUWVN Online Test-Implementing Cisco Unified Wireless Voice Networks (IUWVN) v2.0

Currently, our 642-742 IUWVN online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

A customer recently placed 10 WLCs in a mobility group and now sees a large amount of additional traffic to and from the controller. What setting should be changed to reduce the traffic?

 
 
 
 

When designing a large, high-availability wireless network, what changes to a mobility-group would create less load on the controllers while maintaining the same mobility messages?

 
 
 
 

A network engineer is having wireless multicast fail when it hits the wired network. What command will show the source of multicast groups for troubleshooting?

 
 
 
 
 

After enabling global multicast, multicast traffic has been flooding the wired and wireless network. The wireless engineer has been troubleshooting and is attempting to find the source of the traffic. What command will display the multicast traffic source as well as the incoming interface?

 
 
 
 

A customer is having issues streaming video over wireless in a few high-density areas of their campus. After further investigation, the administrator has singled out the issue pertains to the clients associated to 802.11b/g only access points. The rest of the campus is covered in 802.11n access points. What is a possible reason for the issue with video streaming on the 802.11b/g access points as opposed to the 802.11n access points?

 
 
 
 

Which two critical requirements must be addressed in the RF site survey for wireless video surveillance? (Choose two.)

 
 
 
 
 

When calculating bandwidth usage for an application, what two values represent the minimum and maximum 802.11 overhead per frame? (Choose two.)

 
 
 
 
 
 
 

After implementing mesh with an IP surveillance camera connected to the LAN port on a RAP, the engineer notices that QoS is not being marked. In this setup, what device is responsible for marking upstream traffic from the camera?

 
 
 
 
 

When implementing video teleconferencing over a wireless network, which three attributes should be considered when cell planning? (Choose three.)

 
 
 
 
 
 

A network engineer is configuring CAC on a WLC. If CAC is configured with 85% of the total radio bandwidth on a 5-GHz radio, how many clients can be accommodated?

 
 
 
 

Question 1 of 10

 

cart

 

 

 

23 Mar

200-310 DESGN Online Test-Designing for Cisco Internetwork Solutions

Currently, our 200-310 DESGN online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

Please go to 200-310 DESGN Online Test-Designing for Cisco Internetwork Solutions to view the test

 

cart

23 Mar

640-916 DCICT Online Test-Introducing Cisco Data Center Technologies

Currently, our 640-916 DCICT online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

Please go to 640-916 DCICT Online Test-Introducing Cisco Data Center Technologies to view the test

 

cart

23 Mar

210-060 CICD Online Test-Implementing Cisco Collaboration Devices

Currently, our 210-060 CICD online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

Please go to 210-060 CICD Online Test-Implementing Cisco Collaboration Devices to view the test

 

cart

23 Mar

210-260 IINS Online Test-Implementing Cisco Network Security

Currently, our 210-260 IINS online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

Please go to 210-260 IINS Online Test-Implementing Cisco Network Security to view the test

 

cart

15 Mar

640-911 DCICN Online Test-Introducing Cisco Data Center Networking

Currently, our 640-911 DCICN online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

Please go to 640-911 DCICN Online Test-Introducing Cisco Data Center Networking to view the test

 

cart

03 Mar

200-601 IMINS2 Managing Industrial Networks for Manufacturing with Cisco Technologies

Managing Industrial Networks for Manufacturing with Cisco Technologies is the full name of 200-601 IMINS2 test. There are 65-75 questions in real Cisco 200-601 IMINS2 exam, which will take the candidates 90 minutes to complete the test. The Associated Certification is CCNA Industrial. The available language is English. Candidates can register Cisco 200-601 IMINS2 exam at Pearson VUE testing center.

It is also helpful for the candidates to know Cisco 200-601 IMINS2 exam topics.

1.0 IP Networking 20%

1.1 Describe the difference between enterprise environments and industrial environments
1.2 Describe the components for making the data flow highly available and predictable in an industrial environment (QoS, IP addressing, protocol, and hardware resiliency)
1.3 Interpret and diagnose problems that are related to QoS
1.4 Describe the differences between redundancy and resiliency requirements / approaches between the Enterprise and the plant floor
1.5 Differentiate the capabilities of switch types
1.6 Describe the life cycle of a multicast group
1.7 Describe and configure the operation and use cases for NAT
1.8 Describe and configure the operation and use cases for static routing
1.9 Describe and configure VLAN trunking to a virtual switch
1.10 Describe and configure Layer 2 resiliency protocols (Spanning Tree, REP, Flex Links, and Etherchannels)
1.11 Configure switch ports ( macros, threshold alarms)

2.0 Common Industrial Protocol (CIP) Knowledge and Configuration 19%

2.1 Explain the CIP connection establishment process
2.2 Explain producer/consumer models and implicit/explicit message models
2.3 Recognize communication abilities and capacities in different hardware/hardware generations (revisions)
2.4 Identify and describe the technologies that enable CIP Motion and CIP Safety
2.5 Identify the applicability, limitations, and components of a DLR implementation
2.6 Implement multicast features for CIP within a LAN
2.7 Optimize RPI on a CIP connection given a set of parameters
2.8 Enable and configure IEEE 1588 PTP at the system level
2.9 Configure the Stratix using the Add On Profile (AOP) in Studio 5000

3.0 ProfiNET Knowledge and Configuration 19%

3.1 Describe the differences in ProfiNET support between Cisco catalyst and Cisco Industrial Ethernet (IE) switches
3.1.a Support for VLAN 0
3.1.b Support for ProfiNET LLDP
3.1.c Support for GSDs (integration into SIMATIC STEP 7)
3.2 Describe the operation and purpose of ProfiSAFE
3.3 Describe the three basic ProfiNET devices and conformanceclasses
3.4 Describe the ProfiNET application classes and communication channels
3.5 Describe DHCP and how it can be used for IP addressing of devices and configuration pushes
3.6 Describe ring network requirements for ProfiNET
3.7 Enable ProfiNET on the switch
3.8 Enable Layer 2 QoS to ensure ProfiNET is prioritized
3.9 Integrate the Cisco Industrial Ethernet Switch in SIMATIC STEP 7
3.10 Configure and monitor ProfiNET alarm profiles on IE switches

4.0 Security 12%

4.1 Describe the defense in-depth approach to securing the industrial zone
4.2 Identify how a security component (hardware/software) applies to a network device to meet the network security definition of defense in depth
4.3 Describe network device hardening
4.4 Describe the concept and mechanisms of implementing logical segmentation
4.5 Identify possible options to control traffic between zones (ACLs, firewalls, VLANs)

5.0 Wireless 10%

5.1 Describe the differences between 802.11a/b/g/n/ac
5.2 Describe the components that you need to build multiple wireless networks on a single access point
5.3 Describe the difference between autonomous and controller-based access points and wireless workgroup bridges
5.4 Demonstrate a typical switchport configuration for autonomous and controller-based access points
5.5 Describe the limitations of using a workgroup bridge with a control communication

6.0 Troubleshooting 20%

6.1 Troubleshoot advanced Layer 1 problems such as mechanical deterioration, electromagnetic noise issues, and infrastructure mismatches
6.2 Troubleshoot VLAN trunking
6.3 Troubleshoot an error disabled port
6.4 Troubleshoot basic spanning tree port state and root priority problems
6.5 Troubleshoot Layer 3 problems by inspecting route tables and NAT tables
6.6 Troubleshoot Layer 3 problems in a VRF-lite enabled environment
6.7 Demonstrate the ability to find the location of a device within a multi-switch network given an IP address
6.8 Identify methods for troubleshooting a communication problem in a CIP environment
6.9 Troubleshoot CIP using an Ethernet/IP browse tool, command line, and a web browser
6.10 Troubleshoot device communications performance
6.11 Identify the source of cable and device faults in a DLR
6.12 Identify methods for troubleshooting a communication problem in a ProfiNET environment
6.13 Troubleshoot ProfiNET using SIMATIC STEP 7 to view network topology, use the switch command line

03 Mar

200-601 IMINS2 Online Test-Managing Industrial Networks for Manufacturing with Cisco Technologies

Currently, our 200-601 IMINS2 online test only provide 10 questions. Answer one question correctly, you can get 10 points. The content of these questions are the latest exam content. Please feel free to test your skill level.

If you have some opinions or suggestions about our online test, please leave your message, we will improve it step by step.

Now, begin to test:

Please go to 200-601 IMINS2 Online Test-Managing Industrial Networks for Manufacturing with Cisco Technologies to view the test

 

cart


Recent Posts


Tags

and/or Remove an End-Device and/or Remove an Infrastructure Device and/or Remove Cables (network and/or power) Cisco 642-997 DCUFI exam Cisco 642-999 DCUCI exam Configure Cisco Unity Connection Configure Cisco Unity Express using the GUI Describe and implement centralized call processing redundancy Describe Data Center Structure and Modularity Describe the Design Methodology Describe the Technologies used within the Data Center Describe WLAN Fundamentals Design and Deploy WLAN Infrastructure for Mobility Design Network Management Considerations into a Data Center Design the Access Layer of a Data Center General Networking Knowledge given a Network Design and a set of Requirements High Availability Routing Features Identify Cisco Equipment and Related Hardware Implement high availability features on Cisco Unified Fabric products in a Cisco Data Center Architecture Implement Multicast over Wireless Implement QoS for Wireless Applications Implement VoWLAN Infrastructure Security Infrastructure Services Install Integrate Client Device Security IP Services LAN Switching Technologies Layer 2 Technologies Layer 3 Technologies Maintain Appropriate End-Devices and Industrial Network Infrastructure Devices Manage the Unified Fabric in a Cisco Data Center Architecture Monitoring and Reporting Tools Network Principles Replace Service-Related Knowledge Threat Defense Threat Defense Architectures Troubleshoot Call Setup Issues Troubleshooting Troubleshoot Registration Issues UCS Compute Troubleshooting VPN Technologies WAN Technologies

Links

Powered by CCNP Exams Test Base